- 您现在的位置：买卖IC网 > Sheet目录480 > MTB50P03HDLT4 (ON Semiconductor)MOSFET P-CH 30V 50A D2PAK
MTB50P03HDL, MVB50P03HDLT4G
6
5
4
Q1
QT
Q2
V GS
30
25
20
1000
V DD = 30 V
V GS = 10 V
I D = 50 A
T J = 25 ° C
t r
t f
t d(off)
3
15
100
2
1
I D = 50 A
T J = 25 ° C
10
5
t d(on)
0
0
10
Q3
20
30
40
50
60
V DS
70
0
80
10
1
10
Q T , TOTAL GATE CHARGE (nC)
Figure 8. Gate ? To ? Source and Drain ? To ? Source
Voltage versus Total Charge
R G , GATE RESISTANCE (Ohms)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN ? TO ? SOURCE DIODE CHARACTERISTICS
The switching characteristics of a MOSFET body diode
are very important in systems using it as a freewheeling or
commutating diode. Of particular interest are the reverse
recovery characteristics which play a major role in
determining switching losses, radiated noise, EMI and RFI.
System switching losses are largely due to the nature of
the body diode itself. The body diode is a minority carrier
device, therefore it has a finite reverse recovery time, t rr , due
to the storage of minority carrier charge, Q RR , as shown in
the typical reverse recovery wave form of Figure 12. It is this
stored charge that, when cleared from the diode, passes
through a potential and defines an energy loss. Obviously,
repeatedly forcing the diode through reverse recovery
further increases switching losses. Therefore, one would
like a diode with short t rr and low Q RR specifications to
minimize these losses.
The abruptness of diode reverse recovery effects the
amount of radiated noise, voltage spikes, and current
ringing. The mechanisms at work are finite irremovable
circuit parasitic inductances and capacitances acted upon by
50
V GS = 0 V
T J = 25 ° C
40
30
20
10
0
high di/dts. The diode’s negative di/dt during t a is directly
controlled by the device clearing the stored charge.
However, the positive di/dt during t b is an uncontrollable
diode characteristic and is usually the culprit that induces
current ringing. Therefore, when comparing diodes, the
ratio of t b /t a serves as a good indicator of recovery
abruptness and thus gives a comparative estimate of
probable noise generated. A ratio of 1 is considered ideal and
values less than 0.5 are considered snappy.
Compared to ON Semiconductor standard cell density
low voltage MOSFETs, high cell density MOSFET diodes
are faster (shorter t rr ), have less stored charge and a softer
reverse recovery characteristic. The softness advantage of
the high cell density diode means they can be forced through
reverse recovery at a higher di/dt than a standard cell
MOSFET diode without increasing the current ringing or the
noise generated. In addition, power dissipation incurred
from switching the diode will be less due to the shorter
recovery time and lower switching losses.
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
V SD , SOURCE-TO-DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
http://onsemi.com
5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MTB75N05HDT4
MOSFET N-CH 50V 75A D2PAK-3
MTCBA-C1-N3
MODEM CDMA RS232 DUAL
MTCBA-C1-U-N2
MODEM CDMA USB 800MHZ 1.9GHZ
MTCBA-C1X-N2-NAM
MODEM CDMA 800MHZ 1.9GHZ
MTCBA-G-EN-F4-ED-GB/IE
MODEM GPRS QUAD EU/UK ETH INTFC
MTCBA-G2
MODEM GPRS CELLULAR SERIAL
MTCBA-H-EN2-NAM
WIRELESS ROUTER INTELLIGNT HSDPA
MTCBA-H3-U1
MULTIMODEM CELL WIRELESS MODEM
相关代理商/技术参数
MTB50P03HDLT4G
功能描述:MOSFET PFET D2PAK 30V 50A 25mOhm RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
MTB50SA
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SAM
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SAV
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SAVM
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SB
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SBM
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)
MTB50SBV
制造商:未知厂家 制造商全称:未知厂家 功能描述:Full-Size (7.3mm or 4.7mm height)